ADDER SmartView MultiScreen User's Guide download pdf (Page 16)

 







Mouse button switching modes

You can use a three button mouse to switch between systems. However, when

used in this way, the action of the middle mouse button or scroll wheel click

is ‘trapped’ by the Adder unit and is not passed to the system. This makes it

unavailable for use in controlling applications on the selected system. The scroll

wheel scrolling action is unaffected and passed on normally to the systems, only

the scroll wheel click is used by the Adder unit.

• To use the mouse buttons to change systems, use options U1 (default) or

U4.

• To use the scroll wheel click/third mouse button with the systems, use

options U3 or U5.

• To report only a simple 2-button mouse to the systems, use option U2.

To change the mouse button switching modes

1 Enter conﬁguration mode: Press and hold the SELECT button until the SYSTEM

readout shows c.

2 Press followed by a number to select the required mouse button setting,

as follows:

System channels are switchable using a 3-button mouse or

IntelliMouse (default). Adder unit reports 2-button mouse mode

to the systems.

System channels are not switchable using the mouse. Adder unit

reports 2-button mouse mode to the systems.

System channels are not switchable using the mouse. Adder unit

reports 3-button mouse mode to the systems.

System channels are switchable using a 3-button mouse or

IntelliMouse (default). Adder unit reports IntelliMouse mode to

the systems.

System channels are not switchable using the mouse. Adder unit

reports IntelliMouse mode to the systems.

3 When the mouse button selection has been made, press to ﬁx it and

then press

to exit from conﬁguration mode.

All channel/active channel cycling

The Adder unit provides the option, when cycling between the system channels,

to visit each channel (irrespective of whether an active system is connected)

or to only select active channels. You can affect the keyboard/mouse setting

independently from the front panel SELECT switch setting.

To change keyboard/mouse channel cycling

1 Enter conﬁguration mode: Press and hold the SELECT button until the SYSTEM

readout shows c.

2 Press followed by a number to select the required keyboard/mouse

channel cycling setting, as follows:

Cycle between all ports when switching with ‘hotkeys and Tab’

or three button mouse (default).

Cycle between active ports only when switching with ‘hotkeys

and Tab’ or three button mouse (default).

3 When the channel cycling selection has been made, press to ﬁx it and

then press

to exit from conﬁguration mode.

To change SELECT button channel cycling

1 Remove power from the Adder unit. If any systems are active, either switch

them off or remove their keyboard link connectors from the Adder unit. If an

optional power supply is used, remove it.

2 On the rear panel, click mini switch 6 to the required position, as follows:

• To cycle between all system ports, set switch 6 to OFF.

• To cycle between active ports only, set switch 6 to ON.

3 Re-apply power to the Adder unit.

Automatic screen saver

These conﬁguration options allow you to blank the screen after a set period

of time has elapsed since the keyboard or mouse were last used. Power saving

monitors can sense the screen blanking action and change to sleep mode.

B1 Screen blanking feature disabled (default setting).

B2 Blank screen after 1 minute of inactivity.

B3 Blank screen after 2 minutes of inactivity.

B4 Blank screen after 4 minutes of inactivity.

B5 Blank screen after 8 minutes of inactivity.

B6 Blank screen after 12 minutes of inactivity.

B7 Blank screen after 16 minutes of inactivity.

B8 Blank screen after 20 minutes of inactivity.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22

Comments to this Manuals

No comments

ADDER SmartView MultiScreen User's Guide Page 16

Comments to this Manuals

Related products and manuals for Network switches ADDER SmartView MultiScreen