ADDER SmartView MultiScreen User's Guide download pdf (Page 17)

 







Autoscanning computer selection

These conﬁguration options allow you to determine how the autoscanning

feature chooses which computer to view.

WARNING - When switching between different video sources, some CRT

(Cathode Ray Tube) type monitors will operate an internal mechanical relay at

every switchover - this can be heard as a mechanical ‘click’. To avoid damaging

the mechanical contacts of such relays, do not operate autoscan for long periods

with these types of monitors.

L1 Adder unit locks on to active ports only during autoscanning (default).

L2 Adder unit locks on to every port during autoscanning.

L3 Adder unit powers on in autoscan mode and locks on to active ports only.

L4 SmartView Multiscreen powers on in autoscan mode and locks on to all

ports.

L5 Allow the mouse to run at any speed (default).

L6 Don’t allow the mouse to run at very slow speeds.

L7 Cascade query code = AD (default).

L8 Cascade query code = EF.

Autoscanning dwell timing

These conﬁguration options allow you to determine how long the autoscanning

feature dwells at each computer when scanning between them.

T1 Dwell at each computer for 2 seconds before switching to the next port

(default setting).

T2 Dwell at each computer for 5 seconds before switching to the next port.

T3 Dwell at each computer for 7 seconds before switching to the next port.

T4 Dwell at each computer for 10 seconds before switching to the next port.

T5 Dwell at each computer for 15 seconds before switching to the next port.

T6 Dwell at each computer for 20 seconds before switching to the next port.

T7 Dwell at each computer for 30 seconds before switching to the next port.

T8 Dwell at each computer for 60 seconds before switching to the next port.

Miscellaneous functions

These conﬁguration options contain a mixture of functions, from discovering the

Adder unit internal software (ﬁrmware) revision, to restoring mouse function, to

resetting all conﬁguration changes. Note: These functions use the letter ‘F’. As

with all of the other conﬁguration options, press the letter and then the number,

i.e. F and then 1 – not the ‘F1’ function key.

F1 Display ﬁrmware ﬁrst digit

F2 Display ﬁrmware second digit

F3 Display ﬁrmware third digit

F5 Restore PS/2 mouse operation to the currently selected computer that has

ceased to respond to mouse movement. Note: Before using this function,

please refer to the section ‘Hot plugging and mouse restoration’

F6 Restore IntelliMouse mouse operation to the currently selected computer

that has ceased to respond to mouse movement. Note: Before using this

function, please refer to the section ‘Hot plugging and mouse restoration’

F8 RESET all conﬁguration options to the default settings - see below.

P Initiates password setting mode. Please refer to the ‘Using a password’

section.

E Exits conﬁguration mode and returns your Adder unit to normal operation.

Resetting and restoring default settings

On occasions it may be necessary to reset the Adder unit or to remove all

custom settings and return the Adder unit to its factory default state.

To reset the Adder unit

1 On the rear panel, click mini switch 8 to its ON position for a moment and

then return it to its OFF position.

To restore default settings

1 Enter conﬁguration mode: Press and hold the SELECT button until the SYSTEM

readout shows c.

2 On the connected keyboard, press

and then press , followed by

to perform the restoration of the default settings. The SYSTEM readout will

momentarily show to conﬁrm that the process is complete.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22

Comments to this Manuals

No comments

ADDER SmartView MultiScreen User's Guide Page 17

Comments to this Manuals

Related products and manuals for Network switches ADDER SmartView MultiScreen